Apollo Discovery Manual Call Point 58200-910 and 58200-908

The Apollo Discovery Manual Call Point offers a practical and reliable solution for commercial buildings, hospitals, hotels, offices, warehouses, schools, residential developments, and industrial facilities. Designed as an addressable manual fire alarm device, it allows building occupants to manually activate the fire alarm system when smoke, fire, or another emergency condition is discovered.

For contractors, fire-protection engineers, building owners, property managers, maintenance teams, and safety officers, choosing the correct Apollo Discovery Manual Call Point can help improve emergency reporting, support faster incident identification, and strengthen the overall performance of an addressable fire detection and alarm system.

What Is an Apollo Discovery Manual Call Point?

The Apollo Discovery Manual Call Point is an addressable fire alarm initiating device designed to send a manual alarm signal to a compatible fire alarm control panel.

When a person presses the resettable operating element, the call point communicates an alarm condition through the addressable loop. Because every device is assigned a unique address, the control panel can identify the specific call point and programmed location where the emergency alarm was activated.

The Apollo Discovery Manual Call Point is available in two commonly specified models:

• Apollo 58200-910 – Standard addressable manual call point

• Apollo 58200-908 – Addressable manual call point with built-in short-circuit isolator

These models are commonly used in indoor areas where visible, accessible, and dependable manual fire alarm activation is required.

Key Benefits of Apollo Discovery Manual Call Point

Reliable Manual Fire Alarm Activation

The Apollo Discovery Manual Call Point allows building occupants to immediately activate the fire alarm system after discovering a fire or emergency.

This provides an important additional method of alarm initiation, especially when a person detects a dangerous condition before the automatic smoke or heat detectors respond.

Addressable Device Identification

As an addressable manual call point, the device communicates its unique address to the fire alarm control panel.

This enables the panel to display the programmed location of the activated device, helping security personnel, maintenance teams, and emergency responders identify the reported area more quickly.

Resettable Operating Element

The Apollo Discovery Manual Call Point uses a resettable operating element, allowing the device to be restored after activation or testing without replacing traditional breakable glass.

This can help simplify routine fire alarm testing, system resetting, and ongoing maintenance.

Highly Visible Red Housing

The device features a recognizable red fire alarm housing, making it easier to locate during an emergency.

Its visible design is suitable for installation along escape routes, near exits, in corridors, beside stairways, and in other accessible building locations.

Automatic Communication with the Fire Alarm Panel

Once activated, the Apollo Discovery Manual Call Point automatically sends an alarm signal through the addressable fire alarm loop.

The fire alarm control panel can then initiate programmed actions such as:

• Activating audible and visual alarm devices

• Displaying the activated call point location

• Sending signals to monitoring systems

• Operating programmed fire-safety interfaces

• Initiating emergency procedures

Optional Built-In Short-Circuit Isolator

The Apollo 58200-908 includes a built-in short-circuit isolator.

The isolator helps protect the addressable loop by separating a section affected by a wiring short circuit. This can help maintain communication with other operational devices located on unaffected sections of the loop.

How Does an Apollo Discovery Manual Call Point Work?

The Apollo Discovery Manual Call Point works when a person presses the front operating element during a fire or emergency.

Once pressed, the following sequence normally occurs:

• The internal switch changes to an alarm condition.

• The call point sends a signal through the addressable loop.

• The fire alarm control panel recognizes the assigned device address.

• The panel displays the programmed location of the activated call point.

• The system activates the required alarm outputs and programmed control functions.

A visible indicator helps confirm that the device has been activated.

After the emergency condition has been investigated and the fire alarm system is ready to be restored, authorized personnel can reset the call point using the appropriate reset key.

Apollo 58200-910 Standard Manual Call Point

The Apollo 58200-910 is a standard addressable manual call point designed for indoor fire alarm installations.

It is suitable for projects requiring:

• Manual fire alarm activation

• Individual address identification

• Resettable operation

• Indoor installation

• Connection to a compatible Apollo addressable system

The Apollo 58200-910 is a practical choice for standard addressable fire alarm systems where an integrated isolator is not required at the device location.

Apollo 58200-908 Manual Call Point With Isolator

The Apollo 58200-908 provides the same primary manual alarm activation function while incorporating a built-in short-circuit isolator.

The isolator helps limit the effect of a short-circuit condition on the addressable loop. When a wiring fault occurs, the affected section may be isolated so that devices outside the faulted area can continue communicating with the fire alarm control panel.

This model may be specified for projects that require:

• Additional loop fault protection

• Improved system resilience

• Built-in device isolation

• Compliance with the approved fire alarm loop design

• Reduced impact of short-circuit wiring faults

Common Applications of Apollo Discovery Manual Call Point

An Apollo Discovery Manual Call Point may be considered for the following applications:

• Commercial buildings

• Office developments

• Hotels and resorts

• Hospitals and healthcare facilities

• Schools and universities

• Shopping malls and retail establishments

• Warehouses and logistics facilities

• Residential condominiums and apartments

• Industrial buildings

• Government facilities

• Transportation terminals

• Data centers

• Telecommunications facilities

• Mechanical and electrical rooms

• Indoor fire-protection systems

The selected model must be compatible with the fire alarm control panel, communication protocol, approved system design, and applicable project requirements.

Recommended Installation Locations

Apollo Discovery Manual Call Points are commonly installed in visible and accessible areas such as:

• Near final exits

• Along designated escape routes

• Beside stairway exits

• In corridors and hallways

• Near building entrances

• At changes in floor level

• Near security or fire command areas

• In occupied commercial spaces

• At locations indicated on the approved fire alarm plans

The exact mounting height, spacing, travel distance, and quantity of manual call points must follow the approved fire alarm design, applicable code, project specifications, and authority having jurisdiction requirements.

Why Choose an Addressable Manual Call Point?

An addressable manual call point is often selected when a fire alarm system requires specific device identification, intelligent monitoring, and precise emergency-location reporting.

Unlike a conventional device that may only indicate a general alarm zone, an addressable manual call point provides an individual device address. This allows the control panel to identify the exact call point that was activated based on its programmed description.

The Apollo Discovery Manual Call Point provides a dependable solution for projects where contractors and engineers need:

• Accurate device identification

• Fast manual alarm communication

• Easy resetting after testing

• Reliable addressable-system integration

• Optional short-circuit isolation

• Visible and accessible emergency operation

Apollo 58200-910 vs. Apollo 58200-908

Feature	Apollo 58200-910	Apollo 58200-908
Product type	Addressable manual call point	Addressable manual call point
Manual alarm activation	Yes	Yes
Individual device addressing	Yes	Yes
Resettable operating element	Yes	Yes
Intended installation	Indoor	Indoor
Built-in short-circuit isolator	No	Yes
Primary application	Standard addressable installation	Addressable installation requiring loop isolation

The primary difference is that the Apollo 58200-908 includes an integrated short-circuit isolator, while the Apollo 58200-910 is the standard non-isolated version.

Important Considerations Before Buying

Before selecting an Apollo Discovery Manual Call Point, it is important to confirm the following:

• Exact product model and part number

• Fire alarm control panel compatibility

• Required Apollo communication protocol

• Standard or isolator model requirement

• Indoor or outdoor installation environment

• Surface-mounted or semi-flush installation requirement

• Required operating voltage

• Device-addressing method

• Loop wiring arrangement

• Required accessories and reset key

• Protective cover requirement

• Project specifications and approved plans

• Required product certifications or listings

• Applicable fire-safety codes and local regulations

Correct product selection, professional installation, proper programming, and regular testing are important to help ensure dependable fire alarm system performance.

Installation and Testing Guidelines

The Apollo Discovery Manual Call Point should be installed and commissioned by qualified fire alarm personnel.

During installation and testing, technicians should:

• Verify the approved installation location

• Confirm the correct device model

• Assign the required unique address

• Follow the manufacturer’s wiring diagram

• Observe the required loop polarity

• Secure all wiring terminals

• Confirm the programmed device description

• Activate the call point using the approved test method

• Verify the correct alarm location at the control panel

• Confirm the operation of alarm indicators

• Test the built-in isolator when applicable

• Reset the call point using the correct key

• Record the test result in the maintenance report

Regular inspection and functional testing should be included in the building’s scheduled fire alarm preventive-maintenance program.

Source Your Apollo Discovery Manual Call Point from Pinoleakpes Enterprises Corporation

Pinoleakpes Enterprises Corporation supplies fire alarm devices, fire-protection products, valves, fittings, couplings, piping materials, HVAC controls, and other building-services solutions for commercial, industrial, residential, waterworks, and fire-protection projects.

Our team can help you identify the correct Apollo Discovery Manual Call Point model, isolator requirement, application suitability, and compatible fire alarm components based on your project requirements.

For inquiries about the Apollo Discovery Manual Call Point 58200-910 and 58200-908 with isolator, contact Pinoleakpes Enterprises Corporation today and let us help provide the appropriate manual fire alarm activation solution for your project.